Download more than 100 examples of thesis, proposal and project topics about visco elastic materials in editable WORD file format at undergraduate, graduate and doctoral levels for use and reference in research, articles, theses, student and academic projects.
Master's Thesis in Civil Engineering - Roads and Transportation) Overview Pavements are usually affected by various factors that affect their life. Since a road passes through different areas where the subsoil, the type and volume of traffic and the climatic conditions of these areas are different from each other, therefore, various disadvantages and defects arise in different ...
Master's thesis in the field of civil engineering, structure orientation. Abstract: In this study, the effect of some effective parameters on the strength of polymer concrete based on epoxy resin, including hardener, filler, and solvent, has been investigated. Rice husk ash and broom stalk ash were used as fillers and acetone-toluene mixture with a ratio of 50-50% was used as a ...
Dissertation for master's degree in the field of civil engineering, road and transportation, the abstract of asphalt failures is one of the problems that are the concern of road and transportation engineers today, and every year huge costs are spent on the maintenance and repair of asphalt roads. Many efforts have been made to increase the strength and life of asphalt, among ...
Dissertation for master's degree in civil engineering, structural orientation. Abstract Good bond strength between the old and new concrete surface is a key factor in the performance of concrete repairs. The purpose of this thesis is to investigate and evaluate the bond strength between the surface of the old concrete and the added concrete. In this thesis, a laboratory research ...
Dissertation to receive a general doctorate, abstract, introduction and purpose, among the banding problems in orthodontics, is the creation of decalcified areas around the bands. On the other hand, during the treatment, the bands are prone to loosening and the cement used must have sufficient strength. Recently, new compounds containing amorphous calcium phosphate (ACP) have ...
Master's thesis in the field of polymerization engineering, abstract was determined by using experimental design methods to determine the optimal feed recipe for the preparation of nitrile rubber. Initially, to determine the factors affecting the rate of polymerization, screening tests were designed according to the Plate-Boorman method, which examines a large number of factors ...
Dissertation for receiving a master's degree in chemical engineering, advanced orientation. Abstract The limitation of heat transfer fluids in various industries due to their poor thermal conductivity has caused the improvement of the heat transfer of working fluids to be considered as a new method of advanced heat transfer. So that the idea of ??dispersing solid particles in ...
Master's thesis in the field of mechanical engineering - energy conversion trend Abstract: In this research, the turbulent flow of a non-Newtonian nanofluid in a microchannel with a circular cross-section is simulated. First, the types of classification of microchannels, the methods of making microchannels, as well as the advantages and challenges of using microchannels are ...
Dissertation for M.Sc Mechanical Engineering - Energy Conversion Orientation Abstract: In this research, the turbulent flow of a non-Newtonian nanofluid in a microchannel with a circular cross-section is simulated. First, the types of classification of microchannels, the methods of making microchannels, as well as the advantages and challenges of using microchannels are stated. ...
Mechanical Engineering Master's Thesis - Applied Design Abstract Today, in various industries such as aerospace, atomic energy, chemical industries, refineries, petrochemical industries, etc., there is a need to use high-pressure mechanisms to enable the completion of relevant processes. The increase in pressure is done inside the cylindrical chambers and as a result, such an ...
Master's thesis in the field of mechanical engineering - applied design approach. Abstract: Identifying the stiffness and damping coefficients of a beam support. By: Majid Abedi. Supports and connections play a fundamental and important role in engineering structures. It is necessary to identify different support parameters. Stiffness and damping parameters are the most ...
Master's Thesis in Food Science and Technology (M.Sc) Major: Food Engineering Abstract In this research, the effect of zadu and CHO gums at 5 levels of 0, 0.1, 0.2, 0.28 and 0.4 percent and gum arabic and xanthan gum at levels of 0, 0.5, 0.9, 1.4, 1.8 and 0.08, respectively. 0.1, 0.15 and 0.2% on the stability, rheological and sensory properties of buttermilk during 59 days of ...
Master's Thesis in Mechanical Engineering (Applied Design) Abstract of Gas Turbine Rotor Stress Analysis Using Continuous Damage Mechanics In this thesis, Lometer's unified model based on continuous damage mechanics is used to model the stress-strain behavior of a gas turbine rotor sample. The unified damage law, which is used to model creep-fatigue interaction, is based on the ...
Dissertation for receiving a master's degree in the field of civil engineering in the field of earthquakes. Abstract: The introduction of damage generators is very close to the concept of inelastic behavior and, as a result, hysteresis energy. Therefore, it can be said that the hysteresis energy at these levels can be a significant criterion for the design or control of the ...
Abstract Adopting a suitable currency regime and equilibrium exchange rate is one of the important and sometimes controversial issues. Some economists believe that the low nominal (or real) exchange rate causes export stagnation and reduced incentives for domestic production to replace imports. Others believe that the policy of devaluation of the national currency or high ...
Dissertation to receive M.Sc degree in civil engineering, structural orientation. Abstract: One of the ways to strengthen the building against lateral loads is the use of a wind system (convergent or divergent). The increasing use of steel braces to deal with earthquake forces requires that the seismic performance of these types of systems be given more attention. The common ...
Dissertation for receiving M.SC Master's degree Major: Water Engineering Abstract: Dams are the largest man-made structures. Their design often stems from their unique nature and the consequence of failure, which is certainly greater than the collapse of other types of structures. The stability of dam body and foundation structures can be analyzed and checked in various ways. ...
Civil Engineering Master's Thesis - Soil and Foundation Mechanics Abstract From the past until now, one of the most economical methods to improve the mechanical properties of clay soils has been stabilization by means of additives such as lime and cement in construction projects such as road construction and consolidation of building foundations. Also, with the passage of time ...
Master's Thesis in Mechanical Engineering - Applied Design Abstract In recent years, most of the researches have been focused on compressive and combined loading in order to investigate the buckling of nanotube structures, and for this purpose, the work done on tensile loading is very limited. Since the results of compressive and tensile loading in carbon nanotubes are ...
Dissertation for Master's Degree in Mechanical Engineering (Applied Design) Abstract: Electromechanical micro and nano systems have been noticed due to their distinctive features and unique characteristics, mainly in the two fields of sensors and sensors, in various sciences such as mechanics, aerospace and medicine. Electrostatic stimulation is one of the simplest and most ...
Dissertation for Master's Degree in Applied Design Mechanics Abstract: Composites have received a lot of attention in recent decades due to their high strength and low weight. Such materials can fail due to static, impact, dynamic loading, etc., and the various failures that occur can cause a severe drop in strength in the structure. Engineers always think of using different ...
The thesis for obtaining a master's degree in the field of mechanics, investigating and analyzing the free and forced vibrations of a multi-walled carbon nanotube placed in an elastic medium in order to achieve a clear mathematical understanding of the behavior of different walls of the nanotube under the influence of van der Waals forces and the elastic medium is one of the ...
Dissertation for Master's Degree in Mechanical Engineering Field: Applied Design Abstract In this thesis, stability analysis of composite beam reinforced with carbon nanotubes on elastic support under axial force is investigated. The distribution of nanotubes is assumed to be uniform[1]. To determine the properties of materials reinforced with nanotubes, the results of molecular ...
Master's Thesis in Mechanical Engineering - Applied Design Abstract of elastoplastic analysis of thick-walled tanks made of targeted materials with linear kinematic stiffness behavior under cyclic loading, stress analysis and deformation of spherical thick-walled tanks made of subject materials under internal pressure loading and temperature difference are discussed in this ...
Master's Thesis in Mechanical Engineering (Applied Design): Abstract of the analysis of leading damage in pin connections of composite materials. The purpose of this research is to analyze the leading damage in pin connections of composite materials. To do this, finite element software ABAQUS and FORTRAN programming have been used. The contact between the composite plate with ...
Master's Thesis in Mechanical Engineering (Applied Design) Abstract of three-dimensional interlayer stress investigation in mechanical connections in layered composite materials The purpose of this thesis is to investigate three-dimensional interlayer stresses in mechanical connections in layered composite materials. For this purpose, finite element method and ABAQUS software ...
Thesis - Master's Degree in Geophysics - Winter Seismology 2012 Abstract In this research, the effect of a branch fault in a subduction zone on tsunami waves using numerical modeling of tsunami waves.
Expert thesis Master of Civil Engineering, Structural Orientation, September 2013 Abstract Today, with the progress of science in the construction industry, many methods have been presented to improve reinforced concrete structures
Master's Thesis in Civil Engineering - Earthquake Engineering 1391 Abstract Structures with frames with coaxial braces are among earthquake resistant systems. These structures are widely
Dissertation for Master's Degree in Civil Engineering – Shahrivar Marine Structures, September 1992 Abstract: Pipe-in-pipe systems are widely used in transmission line applications.
Dissertation of Master's Degree in Civil Engineering – Earthquake Engineering 2013 Abstract: Concrete beam and slab bridges with neoprene supports are among the most common highway bridges in the country.
Master's Thesis of Ardakan Faculty of Art and Architecture, Carpet Department (Primary Materials and Dyeing) Mehr 2013 Abstract: During the period of its use, the hand-woven carpet may be affected by various factors and conditions
Master's Thesis in Civil Engineering - Structural Orientation, February 2013 Abstract: The performance of a building during an earthquake depends on many factors, as a result, predicting the seismic performance of structures should be considered either explicitly or implicitly as part of the design or evaluation. Predicting the seismic response of the structure is very ...
Chapter 1 1-1-Introduction: Common fluids such as water, oils and ethylene glycol, which are usually used as heat transfer media, have a limited ability in terms of thermal properties, which is the first obstacle to compress and increase the efficiency of heat exchangers. One of the ways to improve heat transfer is to add particles to the fluid. This method is used for fluids ...
(Strength – Orientation) Economics-Economics, January 2013 Abstract The revenues from the sale of oil have a significant share in the government's income and the government's gross domestic product in Iran. On the one hand, due to the importance of the industrial sector
Abstract The main task of the synchronous generator excitation system is to provide the necessary voltage for the generator excitation winding. The excitation voltage is a dc voltage and it is used to create a flux in the excitation winding of the generator and consequently to produce a magnetic field to produce electrical energy by a synchronous generator. In the provided ...
Dissertation for Master's Degree in Civil Engineering - Structures Abstract: One of the important problems in seismic design and implementation of buildings is the significant dead weight used in it. Therefore, in the case of using lightweight concrete that has favorable mechanical properties, significant benefits can be obtained, including a reduction in dead load and ...
Dissertation for Master's Degree > Direction: Hydraulic Structures Abstract: One of the assumptions that is made to simplify the dynamic analysis of the existing weighted concrete dams is the uniformity of the foundation in terms of physical parameters such as modulus of elasticity and damping. This is despite the fact that, in practice, different geological conditions may ...
Master's Thesis (M.sc) Civil Engineering, Soil and Foundation Mechanics Abstract In this research, the stability of soil reinforced with geogrid located on an underground cavity was analyzed using plaxis software, and the effect of several factors such as the number of geogrid layers, the length of the geogrid layer, the stiffness of the geogrid layer, the optimal location of ...
Master's Thesis in Civil-Structural Engineering Abstract In order to estimate the capacity of buildings, it will be much easier and less expensive to use static methods instead of incremental dynamic methods. Although the incremental dynamic method gives more accurate and closer answers to the real behavior of the structure, its high cost and time has increased the desire to use ...
Master's Dissertation of Discontinuous Structure Abstract: In recent years, the use of composite material in the construction and strengthening of structures has expanded greatly. The structure of this material is such that there is a possibility of crack formation between the layers. Due to the increase in load, these cracks grow and cause a sharp drop in the strength and ...
Dissertation for receiving a master's degree in the field of civil engineering with a focus on soil and foundation. Abstract: The compressibility behavior of soils has become an important concern in geotechnical engineering. As buildings, embankments and roads are implemented, significant settlements often occur. Since long-term settlements occur due to creep, therefore, the ...
Dissertation for Master's Degree in Civil-Structural Engineering Abstract In our country, most of the structures and maybe all the conventional buildings are analyzed and designed independently, which means that these structures are mainly analyzed and designed by conventional software and considering a rigid or articulated support, and then the forces obtained at the base of ...
Master's thesis in the field of structural engineering. Abstract: The increase in vulnerability caused by earthquakes and the large number of earthquake casualties caused by structures and houses that are weak in terms of construction forces people to conduct studies to reduce these risks and damages. Studies such as severe earth movement and seismic hazards related to it play ...
Master's thesis in the field of civil engineering, soil and foundation, today, due to the progress of the tunneling industry, the need to analyze and design underground structures in rocky environments is felt more than in the past. Although there are many numerical and practical software available in this field, none of them are complete and perfect in all fields, and each of ...
Dissertation for Master's Degree in Civil Engineering, Structures, Abstract: This thesis is the results of a numerical and parametric study on the effect of reinforcing reinforced concrete shear wall with FRP composite and applying the results of the finite element method. The finite element program is compared and calibrated against experimental data. Then, the numerical ...
Dissertation for Master's Degree in Civil Engineering with Earthquake Orientation Abstract: Semi-rigid joints [1] are joints whose hardness is between the two states of grip and joint and transmit a part of the anchor, in other words, its degree of rigidity is between 20% and 90%. In this thesis
Master's Thesis in Civil Engineering-Earthquake Abstract Using braces as a lateral resistance system in steel structures is one of the most common methods to withstand the forces caused by earthquakes. One of the weak points of this system is the compression resistance of the bracing member and its buckling as a result of reducing the member's load. Today, this problem has been ...
In order to receive a master's degree in textile technology, it is essential to know the physical and mechanical properties of carpets to produce a quality product and maintain the proper appearance. In this research, an attempt has been made to provide a model to determine the relationship between the different parameters of these characteristics, therefore, to measure these ...
Master's Thesis (Civil Engineering - Water and Wastewater Engineering) Abstract: In this study, ram impact pump modeling was done by the software that was prepared. This software finds the outputs of the HAMMER software as input and by obtaining other information (including the pumping height, etc.) it calculates the amount of pumped water every time the valve is suddenly turned ...
Dissertation for Master's Degree in Civil Engineering, Structures Chapter 1: Introduction-1-Introduction In recent years, the philosophy of traditional methods, which were based on the design of structures against natural hazards, has undergone major changes. Extensive destruction of structures designed on the basis of old regulations in recent earthquakes, advances in analysis ...
Civil Engineering Master's Thesis, Soil and Foundation Engineering Abstract In this thesis, in order to analyze the behavior of surface foundations based on reinforced soil, a simple physical method based on the resistance of materials called ""cone method"" is used, which is actually used as an alternative to the exact solution methods that are based on the three-dimensional ...
Master's thesis in the field of structural civil engineering Abstract: Steel-reinforced concrete is a material that is widely used in civil engineering structures due to reasons such as suitable compressive strength, low cost of preparation and availability of raw materials. But reinforced concrete prepared from cement paste, ordinary aggregates, and steel rebars has weaknesses ...
Dissertation for receiving a master's degree (Sc..M) field: civil engineering, specialization: structure, abstract: In recent years, the subject of seismic isolation has been particularly focused on the seismic design of buildings. The main purpose of this work is to isolate the structure from the ground instead of using conventional retrofitting methods The equipment used in ...
Tendency of soil mechanics and foundations. Abstract: Investigating the behavior of soils due to different loadings is one of the most important issues in geotechnical engineering. The behavior of soils depends on several parameters such as grain size, grain type, loading method, stress history, etc. Non-alignment of main stress and main strain directions is a phenomenon that ...
Introduction In today's era, the presence of waste materials resulting from various physical and chemical processes is one of the important problems of industrialized and developing countries. So that extensive research is being carried out for methods of recycling or disposing of them to minimize the damage to the environment. In this regard, construction researchers, like ...
Doctoral thesis in the field of chemical engineering abstract theoretical and experimental investigation of the continuous process of desalination of heavy crude oil using microwaves and ultrasonic waves Desalination of crude oil is the first step in oil refining, by which the undesirable compounds with the oil are separated before they reach the main unit. In order to reduce ...
A master's thesis in the field of civil engineering - hydraulic structures Abstract Liquid storage air tanks are used not only to store water, but also to store chemicals and toxic substances in different forms. Considering the use of these structures in civil and urban development and industrial networks, their importance is determined before and after the earthquake. The ...
Master's Thesis in Civil Engineering (Soil and Foundation) Abstract Dense sand piles have been used since 1950 in Japan and then in other countries of the world as one of the most effective and economical methods in strengthening soil in order to prevent liquefaction, increase bearing capacity and improve soils with different grain sizes. The process of implementing dense sand ...
Master's thesis in the field of chemical engineering, abstract of the laboratory study of iron oxide production on a microstructural scale using the precipitation method with supercritical anti-solvent by: One of the problems of cement used in oil wells, which are used to connect wall pipes and well walls, is that these cements do not have the desired resistance against high ...
Master's Thesis of Chemical Engineering Abstract In the last few decades, due to the growth of the population as well as the improvement of living standards, the consumption of fibers and the production of textile waste materials have increased greatly. Burial and burning are one of the main ways of managing textile waste materials, which have destructive environmental effects. ...
Dissertation for obtaining a doctorate degree in dentistry. Introduction Removing large amounts of dental tissue weakens the restored tooth. The type of restoration and composite method can be one of the influencing factors on tooth fracture resistance under occlusal forces. The purpose of this study was to investigate the effect of using new low-shrinkage composites on the ...
Dissertation to receive master's degree in organic chemistry Keywords: Farsi: Besparash, condensation, composite, nanocomposite, anchoring Nitrogen in bonding with metals can destroy them
A master's thesis in the field of chemical engineering, abstract of biodiesel production from microalgae by supercritical carbon dioxide extraction method. In this research, different stages of biodiesel production from Chlorella vulgaris microalgae, especially the stage of oil extraction from it, were experimentally studied. The method of microalgae cultivation was selected ...
Master's Thesis in Chemical Engineering Abstract Simulation of dynamic surface tension phenomenon in solvent oil systems based on permeation process is one of the prominent processes in the field of increasing extraction from oil reservoirs, gas injection. Therefore, a correct understanding of the mechanisms and how these processes are carried out is a big step towards ...
Thesis for master's degree in the field: chemical engineering Abstract Hard polyurethane[1] is always considered one of the most effective and practical polymers in various industries, especially the coating industry. Excellent adhesive property, curing ability at ambient temperature and corrosion resistance of this polymer are some of its remarkable features. This study was ...
Dissertation of the doctoral course in the field of chemical engineering, biotechnology, abstract. Heavy oil transportation by pipeline is one of the most important and suitable methods of transportation, and the high viscosity of heavy oil compounds and their sedimentation in the transportation route is the most obvious problem of this type of transportation. Emulsifying heavy ...
Dissertation Chemistry for Master's Degree Abstract Acrylic-based pressure-sensitive adhesives are more expensive than rubber-based adhesives, but they have a longer life and resistance to high temperatures, chemicals, UV rays, solvents, light, softeners, and the environment. Modification of acrylic pressure-sensitive adhesives is useful for improving adhesion properties. In ...
Dissertation for Doctorate Degree in Dentistry Abstract The purpose of this study was to compare the microleakage of adhesive total etch and self etch using three methods of Fluid filtration, dye penetration and dye extraction, as well as to determine the statistical relationship between these three methods. Materials and methods In this laboratory study, 72 extracted human ...
Master's Thesis of Polymer Science and Technology Engineering Abstract Urethane-acrylate resins are of interest due to their low viscosity and flame retardant properties and relatively easy curing. On the other hand, natural fibers with renewable resources, low price, low density and high special properties have a special ability to be used in composites. However, their ...
Dissertation for Master's Degree in Chemistry, Chemistry, Abstract: Epoxy resins, which are thermosetting polymers, have properties such as high thermal stability, good adhesion, high chemical resistance, easy molding, and moisture resistance. These resins are used as adhesives, coatings, paints and polymer tools. The most common epoxy resin is prepared from the reaction of ...
Master's Thesis in Mechanical Engineering, Applied Design, Abstract: Microelectromechanical systems are generally classified based on the type of their excitation mechanism. In addition to electrostatic excitation, which is considered as one of the most important excitation mechanisms, thermal excitation is widely used in multi-layered and functionally variable ...
Dissertation for Master's Degree in Mechanical Engineering (Applied Design) Abstract In this research, the analysis of vibrations, buckling and wave propagation of wrapped nano beam under axial load on Pasternak substrate is discussed. First, the displacement and displacement field of the wrapped beam is obtained. Then, using the obtained displacement field, strain-displacement ...
Dissertation for receiving a master's degree in the field of preservation and modification. Abstract In this research, the effect of combined modification of colloidal silver-hot water on the heat transfer from the hot press plates to the heart of the beech (Fagus orientalis) chipboard cake, the physical and mechanical properties of the chipboard and the chemical changes of the ...
Master's Thesis of Mechanical Engineering-Applied Design Abstract In many applications, graphene (monolayer or multilayer) is used in the polymer matrix as a composite. In this research, ideal graphene with a hexagonal bond shape between atoms, located in a polymer matrix, with different boundary conditions, including gripped and simple, under biaxial external compressive ...
Dissertation for obtaining a doctorate degree in the field of mechanical engineering - manufacturing and production: the advantages of using semi-solid processes are reducing the amount of gas porosity and shrinkage and modifying the microstructure, which aims to improve the mechanical properties of the part. In this research, the cooling ramp method has been used to produce the ...
Abstract Background and Purpose: Emulsions are an important part of most food, pharmaceutical and cosmetic systems, which are very important in various industries due to their special rheological and physicochemical properties. But the main limitation of these systems is their thermodynamic instability, which causes phase separation over time. In this research, the effect of ...
Dissertation for Master's Degree in Food Science and Technology, Food Technology, Abstract: Today, the world is facing a tsunami of non-communicable diseases, among which cardiovascular diseases and cancer are the biggest killers of the century, and blood pressure is known as the leading cause of death for Iranians. Modifying the nutrition style is the key and the way to prevent ...