Download more than 100 examples of thesis, proposal and project topics about thermal conductivity coefficient in editable WORD file format at undergraduate, graduate and doctoral levels for use and reference in research, articles, theses, student and academic projects.
Dissertation for receiving a master's degree in chemical engineering, advanced orientation. Abstract The limitation of heat transfer fluids in various industries due to their poor thermal conductivity has caused the improvement of the heat transfer of working fluids to be considered as a new method of advanced heat transfer. So that the idea of ??dispersing solid particles in ...
Master's thesis in the field of mechanical engineering, energy conversion trend. Abstract: Considering that heat transfer is widely used in various fields of science, it is necessary to use wide recessed or raised surfaces due to physical and spatial limitations in electrical systems. The main purpose of using these surfaces is to increase heat transfer by increasing the ...
Chapter 1 1-1-Introduction: Common fluids such as water, oils and ethylene glycol, which are usually used as heat transfer media, have a limited ability in terms of thermal properties, which is the first obstacle to compress and increase the efficiency of heat exchangers. One of the ways to improve heat transfer is to add particles to the fluid. This method is used for fluids ...
Dissertation for obtaining a doctorate degree in dentistry. Introduction Removing large amounts of dental tissue weakens the restored tooth. The type of restoration and composite method can be one of the influencing factors on tooth fracture resistance under occlusal forces. The purpose of this study was to investigate the effect of using new low-shrinkage composites on the ...
Master's Thesis in Chemical Engineering Abstract: The purpose of this thesis is mathematical modeling of rotary dryer for drying dicalcium phosphate. In this project, with different temperature conditions and different number of cycles of the dryer, the moisture level of the product exiting the dryer has been checked. As a result, 100 data have been obtained from the output of ...
Master's Thesis of Chemical Engineering-Biotechnology Abstract The deteriorating energy sources of fossil fuels will make the developing human society suffer from fuel shortage in the not too distant future. As a result, the concerns of the continuous and increasing release of carbon dioxide into the atmosphere, as well as the extent of pollution caused by fossil fuels that have ...
In order to obtain a master's degree in the field of mechanical engineering, energy conversion, abstract: In this thesis, the mass and heat transfer by integral method in the flow of natural displacement of a fluid with a very low frontal near the wavy inclined wall and under the magnetic field has been investigated. The wall is permeable and as a result, the fluid can be sucked ...
Master's thesis in the field of mechanical engineering - energy conversion trend Abstract: In this research, the turbulent flow of a non-Newtonian nanofluid in a microchannel with a circular cross-section is simulated. First, the types of classification of microchannels, the methods of making microchannels, as well as the advantages and challenges of using microchannels are ...
Dissertation for M.Sc Mechanical Engineering - Energy Conversion Orientation Abstract: In this research, the turbulent flow of a non-Newtonian nanofluid in a microchannel with a circular cross-section is simulated. First, the types of classification of microchannels, the methods of making microchannels, as well as the advantages and challenges of using microchannels are stated. ...
Master's Thesis of Mechanical Engineering-Applied Design Abstract In many applications, graphene (monolayer or multilayer) is used in the polymer matrix as a composite. In this research, ideal graphene with a hexagonal bond shape between atoms, located in a polymer matrix, with different boundary conditions, including gripped and simple, under biaxial external compressive ...
Dissertation for M.Sc. Mechanical Engineering - Manufacturing and Production Trend Abstract The manufacture of square and rectangular pipes has received more attention due to their wide use in industries that require high pressure and temperature. There are different methods for making rectangular tubes, including extrusion, stretching and pressing. Another method that has been ...
Abstract: Research in the field of heat transfer of suspensions with nanometer-sized solid particles in the base fluid has started in the last decade. Recent research in the field of nanofluids has shown that the addition of nanoparticles causes a significant increase in the heat transfer of the suspension. Another common way to improve the thermal performance of devices is to ...
Thesis for receiving a master's degree in the field of mechanics, energy conversion, abstract: free or natural convection heat transfer is one of the most useful phenomena in industry and in the environment around humanity. Due to its wide application, this phenomenon has attracted the attention of many researchers and has prompted researchers to follow the flow of free movement ...
Dissertation for Master's Degree in Mechanical Engineering (Energy Conversion) Abstract In this thesis, the mass and heat transfer of water-aluminum oxide nanofluid in a two-dimensional porous medium under a magnetic field and in the vicinity of a vertical wall has been investigated. The boundary wall can be permeable or impermeable. The concentration and temperature of the wall ...
Master's Thesis on Energy Conversion Abstract: Increasing heat transfer as well as increasing energy efficiency due to the limitation of natural resources and reducing costs has always been one of the most basic concerns of engineers and researchers. This is especially important in fluids due to the small thermal conductivity coefficient. One of the most important ways to ...
Master's Thesis on Energy Conversion Abstract: Increasing heat transfer as well as increasing the efficiency of energy storage systems due to the limitation of natural resources and with the aim of reducing costs has always been one of the most basic concerns of engineers and researchers. This is especially important in fluids due to the small thermal conductivity coefficient. ...
Master's Thesis in Mechanical Engineering (Energy Conversion) Abstract Numerical investigation of three-dimensional heat transfer in traveling wave amplifier collector with input power of 900 and 3000 watts, traveling wave lamp[1] is one of the types of microwave amplifiers. This lamp consists of five main parts, which are electron gun, slow wave structure, wave input and output ...
Master's degree thesis in the field of chemical engineering, thermokinetic and catalyst orientation. Abstract The purpose of this research is to estimate the electrical conductivity of natural waters based on modern mathematical methods. To achieve this, the waters of the Karaj and Jajrud rivers are considered as special cases. For this purpose, 20 sampling stations were ...
Master's Thesis in Mechanical Engineering, Applied Design, Abstract: Microelectromechanical systems are generally classified based on the type of their excitation mechanism. In addition to electrostatic excitation, which is considered as one of the most important excitation mechanisms, thermal excitation is widely used in multi-layered and functionally variable ...
Master's Thesis of Polymer Industry Engineering Abstract Phenolic resins have excellent dimensional, thermal, chemical and corrosion resistance. Also, the fugitives produced during the thermal degradation of this resin have low toxicity and, in addition, they have high charring. Phenolic resins, due to having desirable properties, are used in many fields such as internal parts ...
Dissertation for Master's Degree in Civil Engineering – Shahrivar Marine Structures, September 1992 Abstract: Pipe-in-pipe systems are widely used in transmission line applications.
Dissertation for Master's Degree (M.Sc) Field: Natural Geography - Applied Climatology Abstract Due to its location in a special geographical location, topographic conditions and climatic systems affecting the region, the city of Kavus has a relatively cold climate. So that the air temperature in the coldest month of the year reaches 9.2 degrees Celsius and has the highest ...
Dissertation to receive the master's degree ""M.S.c"" specialization: Textile chemistry and fiber science Abstract: One of the important processes in the completion of textile goods is the underhand improvement in textiles. Finishing the softener provides a desirable softness to the fabric and improves its properties, and the main goals of the softener are to reduce static ...
To receive a master's degree in textile technology engineering. Abstract In the previous research, multi-sized nano-roughness was developed using nanoparticles with different sizes and different surface charges along with silicone resin coating to produce multi-purpose textiles with stable properties. In this research, the idea of ??using laser irradiation and finishing textiles ...
Dissertation for M.Sc. Abstract A wireless sensor network is a network consisting of many small nodes. The node receives information about the environment through sensors. The energy consumption of the nodes is usually provided by batteries, which in most cases cannot be replaced. Therefore, the consumption power of nodes is an important issue in these networks. And it is very ...
Dissertation for master's degree in electricity, power orientation Abstract: The production of electrical energy for power systems with the aim of minimizing the total cost of production for active units in the power network is one of the most important topics for today's modern systems. In other words, the purpose of economic load distribution is optimal and appropriate ...
Master's Thesis in Civil-Structural Engineering Today, domes and arches have found wide applications in architectural and industrial structures due to their suitable coverage of large openings. The use of today's technologies in styling and optimizing energy consumption in these types of structures is one of the important challenges facing engineers. Therefore, the need to ...
Master's Thesis of Water Engineering - Water Resources Management Abstract The advance of salt water in fresh water aquifers is not limited to the islands and coasts of oceans, seas and salt lakes, but it is possible for salt water aquifers to advance through deserts, swamps and salt water pits in the adjacent fresh water aquifers, making it salty and unusable in critical ...
Electrical-Electronics Engineering Master's Thesis Abstract In this thesis, we have used graphene nano-ribbons as an active layer of a solar cell for the first time. To simulate this cell, the non-equilibrium Green's function method was used in the mode space, and the effect of electron-photon interactions was calculated by means of Born's self-consistent approximation. To ...
Master's thesis in the field of chemical engineering (gas engineering trend) in recent years, many horizontal wells have been drilled around the world. The main reason is the ability to increase the level of the tank in contact with the well, which increases the utilization of the well. Well testing is used to identify the models of hydrocarbon reservoirs and to identify their ...
Abstract Gas hydrates are a group of solid host compounds that play an important role in many processes such as gas storage, transfer and separation, heterogeneous catalysis and water purification. These crystals are formed at a temperature higher than the freezing point of water and high pressure. There are different methods to calculate the free energy difference: 1) ...
Master's Thesis in Chemical Engineering, Thermodynamics and Kinetics Abstract: A major part of the final properties of the product in emulsion polymerization is determined by the particle size distribution. In this project, an accurate model based on population balance equations (zero-one model) which includes the phenomena of nucleation and particle growth has been chosen to ...
In order to obtain a master's degree in chemical engineering, abstract freezing of fans in operational units, including the hydrogen unit of Imam Khomeini Shazand Refinery in the cold seasons of the year is one of the important problems in this refinery. In order to provide a suitable solution to this problem, we must have a suitable estimate of the fan outlet temperature. The ...
Master's Thesis (M.Sc.) Direction: Process Design Abstract Currently, membranes have found a special place in different separation industries and have wide applications in different fields of separation, including liquid solutions and different gases. Membrane technology is one of the most widely used technologies in today's industry, whose field of application is wide ranging ...
Master's thesis in the field: Chemical Engineering Abstract In this research, a comprehensive two-dimensional model based on the Finite Element Method (FEM) is proposed for modeling gas-solvent membrane contactors to remove carbon dioxide[1] from synthesis gas. Aqueous solution of monoethanolamine has been used as absorbent solvent stream and CO2/N2 gas mixture as gas stream. ...
Master's degree thesis in the field: Chemical Engineering Abstract In this project, an attempt was made to take a small step towards the synthesis of silicoaluminophosphate molecular sieve in nano dimensions and its use in fuel cells with methanol fuel. Therefore, in this way, nano silicoaluminophosphate was produced under optimal hydrothermal conditions. Next, XRD, FT-IR, SEM ...
Master's Thesis Field: Electricity Major: Electronics Chapter 1 Basics and Generalities Introduction Today, biosensors are used in various fields such as medicine, chemical industry, food industry, environment and the production of medical-health products [1]. In clinical and medical environments, it is very necessary to have tools to diagnose diseases. The development of ...
Doctoral thesis in the field of chemical engineering. Abstract The study of the effective parameters in the synthesis of silver nanoparticles by the inverse microemulsion method of metallic silver nanoparticles is of interest due to their use as catalysts, antimicrobial agents and biosensors. The practical use of silver nanoparticles is highly dependent on the size distribution ...
Thesis of the master's degree in the field: chemical engineering, abstract. In designing the network of heat exchangers, the designer usually considers high operational flexibility in the presented plan. However, some of the changes that occur in the operating conditions of the process after the design, determine the need to modify the existing network. The purpose of the ...
Master's thesis in the field of chemistry, mineral orientation Abstract: Synthesis and identification of the symmetric bis((E)-2-nitrophenylallylidene)-2 and 2-dimethyl-1,3-diamine propane ligands with the general formula MLX2, where M represents zinc (II), cadmium (II) and mercury (II) metals and X includes chloride, bromide, iodide, It is thiocyanate and azide, it was done. To ...
Master's Thesis of Polymer Science and Technology Engineering Abstract Urethane-acrylate resins are of interest due to their low viscosity and flame retardant properties and relatively easy curing. On the other hand, natural fibers with renewable resources, low price, low density and high special properties have a special ability to be used in composites. However, their ...
Dissertation for Master's Degree (M.Sc) Direction: Applied Chemistry Persian Summary According to international standards, the sulfur in the fuels used in the transportation industry, as one of the most important polluting industries, should be reduced to about 10 ppmw, while many refineries in the world produce fuels with a sulfur content of more than 1000 ppmw. One of the new ...
Master's Thesis of Polymer Industrial Engineering Abstract Cross-linked polyethylene is one of the materials that is widely used in the field of insulation production in cables due to having suitable electrical properties and good electrical strength. Nowadays, one of the methods of optimizing the properties and changing the behavior of polymers is the use of filler particles ...
Dissertation for receiving a master's degree in applied chemistry, Persian abstract. In this research, graphite particles were converted to graphene oxide by Hammer's method. Graphene nanoparticles are one of the best and most effective absorbent materials that have been produced so far. Graphene is one of the successful allotropes of carbon in the field of drug absorption and ...
Dissertation for Master's Degree in Mechanical Engineering, Energy Conversion, Abstract Most of the time, initial information and boundary conditions are not precisely defined and cause errors in the output of the problem. These initial values ??can be obtained through experiments and statistical methods. It is often not possible to study individual members of the society due to ...
Dissertation for receiving a master's degree in the field of preservation and modification. Abstract In this research, the effect of combined modification of colloidal silver-hot water on the heat transfer from the hot press plates to the heart of the beech (Fagus orientalis) chipboard cake, the physical and mechanical properties of the chipboard and the chemical changes of the ...
Thesis for obtaining a master's degree in the field: Chemistry, specialization: Analytical Chemistry, Abstract In recent years, the use of nanotubes as nanocarriers for drug delivery has been researched. In this research, carbon nanotubes CNT(5-5), CNT(0-6), BNNT(0-6) and BNNT(5-5) doped with Ga have been used. First, the nanotubes were drawn using Gauss View and Nanotube ...
Master's degree thesis in the field: Electrical Engineering - Power Orientation Abstract: In recent years, with the increasing expansion of electricity consumption, the need to increase energy production and the use of renewable sources in the production of electrical energy has increased due to environmental and economic reasons, among which scattered production units have been ...
Mechanical Engineering Master's Thesis - Applied Design Abstract Today, in various industries such as aerospace, atomic energy, chemical industries, refineries, petrochemical industries, etc., there is a need to use high-pressure mechanisms to enable the completion of relevant processes. The increase in pressure is done inside the cylindrical chambers and as a result, such an ...
Master's Thesis Field: Electricity Major: Electronics Chapter 1 Basics and Generalities 1-1 Introduction Today, biosensors are used in various fields such as medicine, chemical industry, food industry, environment and the production of pharmaceutical-health products[1]. In clinical and medical environments, it is very necessary to have tools to diagnose diseases. The development ...
Dissertation for Master's Degree in Natural Resources (M. Sc) Major: Forestry and Ecology Abstract In this study, the mountain almond reserve (Amygdalus Arabica Olive) in Kolam district of Badreh city in Ilam province, which is a typical reserve, was investigated. First, in the area, the range of the cam reserve, its identification and polygon was digitally closed. Within the ...
Mechanical Engineering Master's Thesis - Energy Conversion Abstract Coating with thin layers plays a very important role in semiconductor industries and microelectromechanical and nanoelectromechanical equipment. By adding a thin layer to the surface due to interference of electromagnetic waves, the radiation properties of the surface will be completely different. In this ...
Abstract This research was conducted in order to investigate the absorption characteristics of cobalt, cadmium and nickel metals using lemon peel. The effect of different parameters such as solution pH, amount of adsorbent, contact time and temperature on the absorption process was investigated and the optimal operating conditions for the absorption of each element on the ...
Master's Thesis in Electrical Engineering ""M.SC."" Direction: Abstract The power of using electric vehicles such as hybrid electric vehicles in the transportation industry is increasing day by day. The battery of these cars can be charged through a home power socket or through public parking lots. Additional load caused by car battery charging can cause harmful consequences on ...
Master's Thesis of Energy Conversion Mechanical Engineering Abstract In recent years, due to the importance of finding energy, global warming and environmental pollution and its production sources, and the growing need of various industries for various forms of energy, as well as the large volume of its consumers around the world, the need to provide models to optimize energy ...
Dissertation for M.Sc Mechanical Engineering - Energy Conversion Trend Abstract In the last century, with the increasing demand for energy and the reduction of fossil fuel resources, the role of renewable energy in the progress and development of countries is not hidden from anyone. In the meantime, wind energy has a special share and has the highest growth rate among other ...
Dissertation for Master's Degree Abstract Achieving higher rates of heat transfer using different techniques that can result in saving a significant amount of energy and also lead to the production of more compact and cheaper devices with higher thermal efficiency has attracted the attention of researchers. Vortex generation is one of the best methods used to increase heat ...
Dissertation for Master's Degree in Mechanical Engineering Field: Applied Design Abstract In this thesis, stability analysis of composite beam reinforced with carbon nanotubes on elastic support under axial force is investigated. The distribution of nanotubes is assumed to be uniform[1]. To determine the properties of materials reinforced with nanotubes, the results of molecular ...
Doctoral Dissertation on Energy Conversion Abstract One of the most important issues in internal combustion engines is heat transfer in them; Because almost a third of the energy produced inside the combustion chamber is removed through engine cooling. The heat transfer of internal combustion engines is important from various aspects, including the protection of materials used ...
Dissertation for M.Sc. Mechanical engineering trend - applied design In this research, a wind turbine with a vertical axis of the Savonius model is modeled. The wind turbine has been modeled in the fluid control volume, which is the same as the wind tunnel in real conditions, and has been investigated under wind blowing with different speeds. Also, in terms of overlap ratio, it ...
Dissertation for Master's degree (M.Sc) orientation: energy conversion. Abstract In this research, a study on irreversible absorption refrigeration systems based on internal and external irreversibility is presented with regard to the limited thermal capacities of external tanks. To optimize the system, three scenarios were defined, in which objective functions such as ...
Dissertation for the Master's degree ""M.Sc"" in Mechanical Engineering - Energy Conversion. Abstract In this thesis, experimental analysis along with numerical simulation has been carried out to investigate the performance of Savunius vertical axis wind turbine. In order to carry out the tests, the turbine was tested in the subsonic wind tunnel. In order to check the accuracy ...
To obtain a master's degree in mechanical engineering - manufacturing and production. Abstract: The electric discharge machining process is one of the advanced machining processes, which is one of the important applications of this process. Despite the unique applications of this machining method, low chipping rate, high surface roughness, high tool wear rate and environmental ...
Master's Thesis in Mechanical Engineering (Energy Conversion) Abstract Numerical investigation of the effect of microstructures on heat transfer and fluid mixing in microchannels, the need for high heat transfer from electronic packages and optical systems, etc., has created a challenge in the field of thermal management. In this context, microchannel heat wells play a great ...
Master's Thesis in Mechanical Engineering - Energy Conversion Abstract The vortex tube is a simple mechanical device that has no moving parts and is one of the equipment used in the refrigeration system, in which a high-pressure fluid enters the vortex tube through the inlet nozzles and splits into two streams with a lower and higher temperature than the inlet temperature, thus ...
Master's Thesis in the field of Mechanical Engineering - Energy Conversion Abstract Numerical investigation of fluid flow and heat transfer on mesh plates with cross holes under discontinuous suction Introduction 1-1- Fluid flow on mesh plates The urgent need of modern humans to use different fuels and the problem of environmental pollution caused by improper and indiscriminate ...
Dissertation for obtaining a master's degree in civil engineering – Spring 2014 structure trend, first chapter, general research 1-1- Introduction: Mostly structures for severe earthquakes and surface acceptance
Dissertation for Master's Degree in Accounting Abstract Accepted principles of accounting have a lot of flexibility in some methods, which potentially makes managers make accounting estimates based on their personal judgments. This flexibility may affect the reliability of accrual items and consequently the stability of these items in successive periods. The main goal of the ...
Dissertation for Master's Degree Abstract: Dealing with external forces such as earthquakes is one of the most important missions of civil engineers. In order to achieve this goal, the light metal frame system, which has advantages such as the possibility of industrial production, prefabrication and lightness, can be considered as a suitable alternative to traditional systems. ...
Dissertation for M.A. degree Abstract of this research, knowing the conditions governing the Fahlian River, determines the Manning roughness coefficient in the studied area using various experimental and semi-experimental methods and tables for use in designs. And it presents the best and most reliable method of determining the roughness coefficient using field studies and ...
Dissertation for master's degree in civil engineering, structural orientation. Abstract: Today, in earthquake-prone countries, it is recommended to use a variety of energy-depleting tools in order to dissipate the energy of earthquakes on the structure. One of these tools is rotational friction dampers. Because the current regulations do not provide a value for the coefficient ...
Dissertation for Master's Degree in Mechatronics Abstract In this thesis, a phase-locked loop is designed based on micro-electromechanical systems. The loop system has a feedback phase lock that compares the input phase with the output phase. This comparison is done by a phase detector. Phase detector is a circuit whose average output voltage is linearly proportional to the ...
Master's Thesis in Accidents Abstract: Vehicle traffic safety is one of the most basic principles in traffic engineering and transportation planning in the world. Non-observance of safety principles in the design of roads, maintenance and planning of transportation and traffic in the country has caused heavy damages to the society. Slip resistance[1] is considered as one of the ...
Civil Engineering Master's Thesis - Soil and Foundation Mechanics Abstract From the past until now, one of the most economical methods to improve the mechanical properties of clay soils has been stabilization by means of additives such as lime and cement in construction projects such as road construction and consolidation of building foundations. Also, with the passage of time ...
Dissertation for Master's Degree in Civil Engineering - Structural Orientation Abstract: The most basic goal in the seismic design of structures is to prevent the structure from collapsing during severe earthquakes, which is the basis of the governing theory of seismic behavior, the result of investigating the nonlinear behavior of the structure during an earthquake and the ...
Master's Thesis in Chemical Engineering, Process Design, Abstract: In this thesis, a method for thermodynamic analysis and evaluation of energy consumption of distillation tower by using side cooling is introduced. The research done in the past was aimed at the distribution of the heat diagram and checking the possibility of adding or extracting heat from all the different parts ...
Dissertation for Master's Degree (M.Sc.) Direction: Chemical Engineering Abstract It has been less than two centuries that the preparation and distribution of food in a commercial manner and gradually modernized today to where any type of product or product can be purchased in any season, but since food is a perishable substance, different methods have been created for long-term ...
Presented to graduate education management as a part of the educational activities required to obtain a master's degree, the dimensions of MEMS components according to Figure (1-2) include a wide range, from dimensions smaller than one micrometer that are not visible to the eye to dimensions of one millimeter, also types of these systems can be in a simple state, a tool without ...