Download more than 28 examples of thesis, proposal and project topics about rotor in editable WORD file format at undergraduate, graduate and doctoral levels for use and reference in research, articles, theses, student and academic projects.
Dissertation of the master's course in electrical field (M. Sc) orientation: power Abstract: In this thesis, electrical and mechanical defects in electric machines are examined and the factors that cause them and the methods of fixing these defects are stated. After that, with the help of the winding function method of the simulation machine and the intended error, i.e. the ...
Dissertation of the Master's course in the field of electricity (M. Sc) orientation: power Abstract: In this thesis, electrical and mechanical defects in electric machines are first examined and the factors causing them and the methods of fixing these defects are stated. After that, with the help of the winding function method of the simulation machine and the intended error, ...
Master's Thesis Applied Design Abstract In this thesis, in the field of vacuum technology, the importance, application and role of this technology in the industry and the advancement of scientific research, technical terms related to this technology, types of vacuum pumps, applications, advantages and disadvantages of each of the vacuum pumps, the importance of studying the ...
Master's Thesis in Mechanical Engineering (Applied Design) Abstract of Gas Turbine Rotor Stress Analysis Using Continuous Damage Mechanics In this thesis, Lometer's unified model based on continuous damage mechanics is used to model the stress-strain behavior of a gas turbine rotor sample. The unified damage law, which is used to model creep-fatigue interaction, is based on the ...
Dissertation for Master's Degree in Electrical Engineering (M.Sc) Abstract The power system stabilizer is added to the excitation system in order to improve the damping of the power system during low frequency disturbances. For large-scale power systems that include a large number of connected generators, setting the power system stabilizer parameters will be a complex and ...
Dissertation for M.sc degree, field: electricity, orientation: power electronics. Abstract Voltage stability is related to the power system's ability to maintain acceptable voltages in all system buses under normal conditions and after disturbance. The system enters an unstable state when a disturbance, an increase in the required load or a change in the system's position causes ...
Dissertation for receiving a master's degree, field of study: electricity-power, orientation: electric machines in a synchronous generator, a dc current is applied to the rotor coil to produce a magnetic field. Then the rotor of the generator is rotated by a prime mover to create a rotating magnetic field in the machine. This magnetic field induces a three-phase voltage in the ...
Abstract The main task of the synchronous generator excitation system is to provide the necessary voltage for the generator excitation winding. The excitation voltage is a dc voltage and it is used to create a flux in the excitation winding of the generator and consequently to produce a magnetic field to produce electrical energy by a synchronous generator. In the provided ...
Master's Thesis of Electrical Engineering - Power Abstract: Induction motor condition monitoring is an absolutely necessary and important technology to detect various defects at the initial stage. which can prevent the spread of unexpected defects in the initial stages. Approximately 30-40% of induction motor defects are related to stator defects. In this thesis, a comprehensive ...
Master's thesis in the field of electricity-power orientation Abstract Gearboxes are essential and inseparable components of power transmission systems. These machines convert torque into speed and sometimes speed into torque. The use of mechanical gearboxes in these systems has been common since long ago as an interface between the power generation sector and the power ...
Master's thesis in the field of electrical engineering - power abstract of the possible analysis of dynamic stability of microgrids, considering wind turbines, in recent years, the high penetration of renewable energy sources, especially wind energy, in power networks has created new problems. One of the most important issues is the uncertainty in the power produced by wind ...
Master's thesis in the field of electrical engineering (power trend) Abstract of the investigation of transient electromagnetic states in wind turbines with the increasing development of wind turbines, increasing its efficiency has become more critical. One of the factors for measuring wind turbine efficiency is its performance in transient state problems. The phenomena that ...
Master's Thesis, Electrical Engineering, Power, Abstract: The sliding mode control method is one of the most important non-linear control methods, whose distinctive characteristics are insensitivity to parameter changes, complete rejection of disturbance, and dealing with uncertainty. This controller first brings the system from the initial state using the law of reaching the ...
Master's Thesis in Electrical Engineering, Power 1-1 Introduction Energy supply sources in the last few decades have been from fossil sources, which until recently have been obtained almost cheaply. Cheap energy sources caused that the optimal use of energy and energy recycling were practically not paid much attention. Due to the energy shortage crisis and the sense of danger ...
Master's thesis in the field of electricity-power orientation Abstract Gearboxes are essential and inseparable components of power transmission systems. These machines convert torque into speed and sometimes speed into torque. The use of mechanical gearboxes in these systems has been common since a long time until now as an interface between the power generation sector and the ...
Dissertation for receiving a master's degree, field of study: electricity-power, orientation: electric machines 1.1 Introduction: In a synchronous generator, a dc current is applied to the rotor coil to produce a magnetic field. Then the rotor of the generator is rotated by a prime mover to create a rotating magnetic field in the machine. This magnetic field induces a ...
Abstract Photovoltaic or PV for short is one of the types of electricity generation systems from solar energy. In this method, by using solar cells, direct production of electricity from sunlight becomes possible. Solar cells are semi-conductors that are made of silicon, the second most abundant element in the earth's crust. When sunlight shines on a photovoltaic cell, a ...
Dissertation for Master's Degree in Electrical Engineering (M.Sc) Major: Power System Abstract Stabilizer is added to the excitation system in order to improve the damping of the power system during low frequency disturbances. For large-scale power systems that include a large number of connected generators, adjusting the power system stabilizer parameters will be a complex and ...
Dissertation for receiving a master's degree in the field of electricity - the tendency of electric machines. Abstract In this thesis, the behavior of the wind power plant is investigated using the detailed model of induction generator with two-way feeding. Electronic converters of the power plant and its control systems and the behavior of the power plant include electrical and ...
Dissertation for receiving a master's degree in the field of electrical power, power systems trend. Abstract: Reactive power compensation has always been one of the important research topics in most universities and research centers. Meanwhile, the new generation of compensators (FACTS) has been the focus of the power industry and research centers in order to control reactive ...
Dissertation for M.Sc Mechanical Engineering - Energy Conversion Trend Abstract In the last century, with the increasing demand for energy and the reduction of fossil fuel resources, the role of renewable energy in the progress and development of countries is not hidden from anyone. In the meantime, wind energy has a special share and has the highest growth rate among other ...
Dissertation for M.Sc. Mechanical Engineering - Manufacturing and Production Trend Abstract The manufacture of square and rectangular pipes has received more attention due to their wide use in industries that require high pressure and temperature. There are different methods for making rectangular tubes, including extrusion, stretching and pressing. Another method that has been ...
Dissertation for M.Sc. Mechanical engineering trend - applied design In this research, a wind turbine with a vertical axis of the Savonius model is modeled. The wind turbine has been modeled in the fluid control volume, which is the same as the wind tunnel in real conditions, and has been investigated under wind blowing with different speeds. Also, in terms of overlap ratio, it ...
Mechanical Engineering, Manufacturing and Production Department, Master's Thesis, Introduction High-speed rolling bearings have many applications in rotating machines, whose task is to separate the rotating parts from the fixed parts of the machine. Accuracy is very important in machine tool applications and bearing corrosion resistance in chemical machines. In aerospace ...