Download more than 73 examples of thesis, proposal and project topics about interlayer crack in editable WORD file format at undergraduate, graduate and doctoral levels for use and reference in research, articles, theses, student and academic projects.
Master's Dissertation of Discontinuous Structure Abstract: In recent years, the use of composite material in the construction and strengthening of structures has expanded greatly. The structure of this material is such that there is a possibility of crack formation between the layers. Due to the increase in load, these cracks grow and cause a sharp drop in the strength and ...
Master's Thesis Abstract In this project, the coat cracker unit of Abadan refinery has been simulated using Hysys refinery software. In simulating and receiving information, feed properties and solving mass and energy balance equations have been used. Simulation data and operational data of Abadan Cat Cracker unit have been compared. Also, by changing some important operational ...
Thesis Mechanics to get a Master's degree Abstract: First, the solution of Volterra-type anti-plate displacement in a rectangular plate with limited length and width and different boundary conditions is obtained by the method of separation of variables. Then, the distributed displacement technique is used to obtain the integral equations related to the rectangular plate weakened ...
Dissertation for Master's Degree in Rock Mechanics Abstract The unexpected stress intensity factor of some engineering structures has caused a lot of financial and collateral damage. In investigating the causes of failure, researchers gradually found that the design of many of these structures was correct based on the theory of elasticity and resistance of materials, and the ...
Presented to obtain a master's degree in the field of mechanical engineering-applied design orientation. Abstract In this research, we investigated the free vibration of a cracked beam and found its natural frequencies. In the first part, by using the open crack model, by modeling the cracked part as a beam-shaped element and satisfying the boundary conditions, we obtained the ...
Master's Thesis in Mechanical Engineering (Applied Design) Abstract of three-dimensional interlayer stress investigation in mechanical connections in layered composite materials The purpose of this thesis is to investigate three-dimensional interlayer stresses in mechanical connections in layered composite materials. For this purpose, finite element method and ABAQUS software ...
Dissertation for obtaining a master's degree in civil engineering, structural orientation, March 2013, abstract of the scope of using FRP materials for shear strengthening of reinforced concrete beams in
Thesis of master's degree in civil engineering, soil and foundation mechanics orientation, September 2019, abstract: analysis of dynamic interaction between soil and structure (due to the mutual effect of the structure and its retaining soil on each other), D
Dissertation for Master's Degree in Educational Planning Summer 2019 Abstract: This research aims to investigate the quality of services of educational complexes in districts 1 and 2 of A
Summer 1390 Expertise Master of the field: Civil Engineering Orientation: Structure Abstract: In this thesis, the effect of nanosilica on the mechanical properties and durability of concrete containing polypropylene fibers
Dissertation of master's degree in civil engineering, structural orientation, October 1390, first chapter of generalities. 1-1 Introduction In recent years, there have been many advances in the field
Doctoral dissertation in civil engineering – Earthquake Engineering 2013 Abstract The inappropriate performance of columns in concrete buildings designed and built in the past years causes concern and attention to the amount of A
Thesis for obtaining a master's degree, field: natural geography, orientation: geomorphology in environmental planning, abstract, one of the pillars of the tourism industry is the existence of tourist attractions, especially natural attractions, which form the primary capital of the tourism industry. Seas, forests, meadows, mountains, valleys, waterfalls, mines, springs are ...
Dissertation for M.A. Master's Degree Field: Psychology Orientation: Clinical Abstract A common problem in substance abuse disorders is drug relapse even among treated individuals, which is more applicable to the narcotic drug glass. On the other hand, mindfulness is a cognitive structure that can be monitored and intervened in psychology. The main goal of this research is to ...
Dissertation for obtaining a master's degree in the field: natural geography, specialization: tourism planning. This research deals with the development of geotourism in the Vashi Gorge of the Jalizjund basin of Firuzkoh city by using a descriptive and analytical method with practical objectives, and the method of collecting information is in the form of library, document and ...
Dissertation for M.A) degree in Organizations and Methods Abstract Today, human resources development and employee empowerment is one of the effective tools to increase productivity and optimal use of their individual and group capacities and abilities in line with organizational goals and to better express organizational efficiency and effectiveness. In the current situation, ...
Dissertation to receive a master's degree (M.A) in natural geography, specialization: climatology in environmental planning, abstract: natural disasters have been the most important cause of human concern at all times. Landslides are one of the most important natural disasters that cause financial and human losses every year, which creates problems in the implementation of ...
Abstract The main task of the synchronous generator excitation system is to provide the necessary voltage for the generator excitation winding. The excitation voltage is a dc voltage and it is used to create a flux in the excitation winding of the generator and consequently to produce a magnetic field to produce electrical energy by a synchronous generator. In the provided ...
Master's Thesis in Civil Engineering - Roads and Transportation) Overview Pavements are usually affected by various factors that affect their life. Since a road passes through different areas where the subsoil, the type and volume of traffic and the climatic conditions of these areas are different from each other, therefore, various disadvantages and defects arise in different ...
The effect of fiber and pozzolanic materials on the mechanical properties of glass fiber reinforced concrete Master's Thesis of Civil-Structural Engineering Abstract The failure and destruction of concrete is highly dependent on the formation of cracks and microcracks. With increasing loading, microcracks are connected and form cracks. In order to solve this problem and also to ...
Dissertation for Master's Degree in Civil Engineering, Soil and Foundation Mechanics Abstract: Fine-grained clay soils have always caused problems in construction projects, one of the ways to improve the properties of problematic clay soils is to use lime to stabilize the soil. It swells. this
Dissertation for Master's Degree in Civil Engineering - Earthquake Engineering Abstract The city of Birjand, as the capital of South Khorasan province, is located in the structural zone of Sistan, which is particularly sensitive due to its proximity to seismic and fundamental faults (Neh Khawri and Westi faults in the south, Ardkol fault in the northeast, Nawaz fault in the ...
Dissertation for Master's Degree in Public Administration Abstract: The purpose of this research is to determine the relationship between spiritual intelligence, job satisfaction, and organizational commitment among the employees of Tehran Pharmaceutical Company. The statistical population of the research includes all the male and female employees of Daro Pasha company in ...
Dissertation for master's degree in the field of civil engineering, road and transportation, the abstract of asphalt failures is one of the problems that are the concern of road and transportation engineers today, and every year huge costs are spent on the maintenance and repair of asphalt roads. Many efforts have been made to increase the strength and life of asphalt, among ...
Dissertation for Master's Degree in Civil-Structural Engineering Abstract In our country, most of the structures and maybe all the conventional buildings are analyzed and designed independently, which means that these structures are mainly analyzed and designed by conventional software and considering a rigid or articulated support, and then the forces obtained at the base of ...
Master's Thesis in Civil-Soil Field Abstract Dense clay layers are used as one of the most common impermeable layers in most geotechnical structures such as earthen dams and municipal and radioactive waste disposal centers. Due to special geotechnical characteristics, these layers are damaged by cracking during their lifetime, these cracks increase the permeability of the layer ...
A master's thesis in the field of computer-software engineering. Software vulnerabilities can lead to financial and information losses. Due to the limited financial and human resources, prioritizing the damages is very important. Before this research, a large number of researchers have classified vulnerabilities based on empirical and statistical knowledge. However, the variable ...
Dissertation for Master's Degree in Civil Engineering, Structures, Abstract: This thesis is the results of a numerical and parametric study on the effect of reinforcing reinforced concrete shear wall with FRP composite and applying the results of the finite element method. The finite element program is compared and calibrated against experimental data. Then, the numerical ...
Dissertation for Master's Degree in Civil Engineering with Earthquake Orientation Abstract: Semi-rigid joints [1] are joints whose hardness is between the two states of grip and joint and transmit a part of the anchor, in other words, its degree of rigidity is between 20% and 90%. In this thesis
Master's Thesis in Civil Engineering-Earthquake Abstract Using braces as a lateral resistance system in steel structures is one of the most common methods to withstand the forces caused by earthquakes. One of the weak points of this system is the compression resistance of the bracing member and its buckling as a result of reducing the member's load. Today, this problem has been ...
In order to receive a master's degree in textile technology, it is essential to know the physical and mechanical properties of carpets to produce a quality product and maintain the proper appearance. In this research, an attempt has been made to provide a model to determine the relationship between the different parameters of these characteristics, therefore, to measure these ...
Dissertation of Master's Degree in Civil Engineering - Structure Abstract In metal structures, one of the most important places of stress concentration is the joint. In form cutting, the shear force at the connection point is so high that a part of the beam or its reinforcement is broken and separated in pieces, and this is due to negligence in the design of the connection or ...
Master's Thesis Field: Civil Engineering Abstract Bridges are inseparable members of the means of communication and are very influential in economic and social conditions. The passage of time and random loads are among the things that threaten the health of bridges. Abnormal loads caused by natural accidents, execution errors and some other issues can cause progressive collapse ...
Dissertation for Master's Degree in Mechatronics Engineering Persian Abstract The purpose of this project is to introduce a new approach for troubleshooting gas transmission pipelines using mechanical waves, which is much cheaper and easier than other methods. who are currently working. These lines are usually located in difficult environmental conditions and far away and in ...
Dissertation for master's degree in civil engineering, structural orientation. Abstract Good bond strength between the old and new concrete surface is a key factor in the performance of concrete repairs. The purpose of this thesis is to investigate and evaluate the bond strength between the surface of the old concrete and the added concrete. In this thesis, a laboratory research ...
Dissertation for receiving M.SC Master's degree Major: Water Engineering Abstract: Dams are the largest man-made structures. Their design often stems from their unique nature and the consequence of failure, which is certainly greater than the collapse of other types of structures. The stability of dam body and foundation structures can be analyzed and checked in various ways. ...
Education Level: Master's Degree, Field: Civil Engineering, Major: Structures Abstract: In this thesis, the effect of nanosilica on the mechanical properties and durability of concrete containing polypropylene fibers was investigated. Polypropylene fibers with a length of 18 mm and a ratio of length to diameter of 0.9 mµ were used. The effect of fibers and nanosilica in three ...
Master's thesis in the field of civil engineering, structure orientation Alkaline Aggregate Reaction [1] (AAR), is a chemical reaction that occurs in some concrete structures. (AAR) is a reaction between alkaline fluids in the pores and silica aggregates. Concrete failure, including expansion and cracking due to the alkaline reaction of aggregates, is of particular importance. ...
Master's thesis in the field of structural civil engineering Abstract: Steel-reinforced concrete is a material that is widely used in civil engineering structures due to reasons such as suitable compressive strength, low cost of preparation and availability of raw materials. But reinforced concrete prepared from cement paste, ordinary aggregates, and steel rebars has weaknesses ...
Dissertation to receive the master's degree ""M.Sc. Orientation: ""Biochemical Engineering"" Abstract: The presence of sulfur compounds in gasoline creates a serious problem in air pollution, environment, corrosion of equipment and destruction of human health. The new environmental standards also impose strict limits on the amount of sulfur and aromatic compounds in gasoline. ...
Dissertation to receive a master's degree in the field of Analytical Chemistry, Abstract Biosynthesis of gold nanoparticles with small size and biological stability are very important and have various biomedical applications. In this work, an easy and simple method for the green synthesis of gold nanoparticles using willow tree bark extract is reported. The bark of the willow ...
Dissertation for Master's Degree (M.Sc) Major: Applied Chemistry Persian Summary The purpose of this research is to investigate common fatty acids in ostrich oil and determine the amount of retinol in snail secretion to make a cream with therapeutic properties. Since 3000 years ago, the healing properties of ostrich oil have been known to treat wounds, burns, joint pain and skin ...
Master's thesis in the field of chemical engineering (gas engineering trend) in recent years, many horizontal wells have been drilled around the world. The main reason is the ability to increase the level of the tank in contact with the well, which increases the utilization of the well. Well testing is used to identify the models of hydrocarbon reservoirs and to identify their ...
Introduction In today's era, the presence of waste materials resulting from various physical and chemical processes is one of the important problems of industrialized and developing countries. So that extensive research is being carried out for methods of recycling or disposing of them to minimize the damage to the environment. In this regard, construction researchers, like ...
M.Sc. Dissertation for Master Degree in Chemical Engineering - Process Engineering Abstract Mercaptans are removed from hydrocarbon streams by various methods. The use of caustic soda solution and mucoli sieve beds are among the most widely used methods. In the oil and gas industries of our country, washing with relatively dilute caustic solution is often used to remove light ...
Dissertation for receiving the master's degree ""M.Sc"" orientation: abstract structure In today's reinforced concrete buildings, the use of interframe separators is very common. Intermediate frames with building materials are the main types of separators that are used in this type of buildings. In previous research, these interframe separators are usually considered as ...
A master's thesis in the field of civil engineering - hydraulic structures Abstract Liquid storage air tanks are used not only to store water, but also to store chemicals and toxic substances in different forms. Considering the use of these structures in civil and urban development and industrial networks, their importance is determined before and after the earthquake. The ...
Master's thesis in the field of chemical engineering, abstract of the laboratory study of iron oxide production on a microstructural scale using the precipitation method with supercritical anti-solvent by: One of the problems of cement used in oil wells, which are used to connect wall pipes and well walls, is that these cements do not have the desired resistance against high ...
Dissertation for obtaining a doctorate degree in dentistry. Introduction Removing large amounts of dental tissue weakens the restored tooth. The type of restoration and composite method can be one of the influencing factors on tooth fracture resistance under occlusal forces. The purpose of this study was to investigate the effect of using new low-shrinkage composites on the ...
Dissertation to receive a general doctorate, abstract, introduction and purpose, among the banding problems in orthodontics, is the creation of decalcified areas around the bands. On the other hand, during the treatment, the bands are prone to loosening and the cement used must have sufficient strength. Recently, new compounds containing amorphous calcium phosphate (ACP) have ...
Dissertation for Master's Degree in Nursing Education (Internal Surgery) Abstract Introduction: Foot ulcers are the most common, serious and costly complications of diabetes and increase the risk of death in diabetic patients by 2-4 times. Also, diabetic foot is one of the main causes of disability in patients with diabetes mellitus and one of the chronic and preventable ...
Master's thesis in the field of chemical engineering without major. Abstract: Modeling, simulation and optimization of Jam Petrochemical Check Bed Reactor for hydrogenation of 1 and 3-butadiene. Therefore, a suitable kinetic model has been selected as a basic structure for modeling the reactor, and after that the presented model has been developed in order to match the molar ...
Mechanical Engineering Master's Thesis Proposed Design - Introduction The use of fibers in concrete started about 50 years ago and day by day their use in various fields has increased. Adding fibers to the mixing design improves the mechanical properties of concrete and the behavior of the structure after cracking. It also increases the softness and malleability of the section. ...
Master's Thesis of Polymer Industry Engineering Abstract Phenolic resins have excellent dimensional, thermal, chemical and corrosion resistance. Also, the fugitives produced during the thermal degradation of this resin have low toxicity and, in addition, they have high charring. Phenolic resins, due to having desirable properties, are used in many fields such as internal parts ...
Dissertation for Master's Degree in Analytical Chemistry Abstract Nowadays, nanostructures have attracted the attention of many researchers due to their new features and applications in different fields and branches of science and technology. Meanwhile, nanocomposites, due to their unique physical and chemical properties, as well as potential applications in catalytic, ...
Master's Thesis in the field of Electrical Engineering - Telecommunications Abstract The improvement of slotted wave array antenna to reduce the sidelobe area and cross polarization of slotted wave antennas were introduced in 1943 at McGill University. The simple structure, high efficiency and linear polarization of these emitters have made them popular in many radar ...
Master's Thesis of Electrical Engineering-Communications Wave Orientation Abstract In this thesis, identification of the position and shape of two-dimensional metal objects by optimization[1] of the cost function[2] with the help of the level setting method[3] and the simulation results are presented. In this method, we were able to obtain the shape and position of the objects ...
Field of study: Mechanics, orientation: energy conversion. The present research was conducted in order to investigate the movement of pig in pipelines. Due to the importance of pipelines in providing energy resources in the world, after installation and operation, the maintenance of these lines is of high importance, which has caused special attention to be paid to the design of ...
Dissertation for M.Sc) in the field of mechanics in the field of construction and production. Abstract In the present research, the design and construction of the ECAR machine in order to investigate the effects of the process on carbon steel sheets was our goal. The desired research was carried out in the research workshop of Islamic Azad University, Jaseb branch. After the ...
Dissertation for Master's Degree in Horticulture-Fruit Science Abstract Rish Baba grape variety is one of the most popular fresh edible cultivars cultivated in Iran, but usually the pods have poor color. In this study, the effect of ring removal and ethfen treatments on the quantitative and qualitative traits of 'Rish Baba Garmez' grape variety was investigated. The experiment ...
Thesis for obtaining a master's degree in the field: agricultural engineering, horticultural sciences, specialization: physiology and breeding of fruit trees. Abstract: Drought stress is one of the most important factors limiting the growth of plants in arid and semi-arid regions of the world, such as Iran. The importance of using water resources and the occurrence of recent ...
Dissertation for Master's degree (M.Sc.) Direction: Watershed, the effect of different components of rainfall on the morphometric characteristics of landslides in Mazandaran province. Abstract: Landslide is one of the main landslide processes that affects the evolution of mountainous regions and causes catastrophic events. Landslides in Iran, especially in the northern basins of ...
Master's Degree Thesis Abstract With the advancement of technology, the need to use new materials is felt. New methods have been developed to make new materials. Among the new materials in progress, we can mention double-layer sheets. These materials have composite properties of composite materials. The purpose of this research is to produce a double-layer sheet of 304L ...
Dissertation for Master's Degree in Rock Mechanics Introduction Excavations made in rocks have different dimensions according to their purpose and vary from small dimensions to dimensions comparable to huge concrete structures. Surface excavations can be used as a space for extracting mines, creating buildings, and supporting and overflowing dams, factories, power plants, as ...
Dissertation for Master's Degree in Mechanical Engineering Field: Applied Design Abstract In this thesis, stability analysis of composite beam reinforced with carbon nanotubes on elastic support under axial force is investigated. The distribution of nanotubes is assumed to be uniform[1]. To determine the properties of materials reinforced with nanotubes, the results of molecular ...
Dissertation for receiving a master's degree in electrical engineering field telecommunication field Abstract This thesis focuses on the applications and development of Time-Reversal techniques based on signal processing methods for broadband electromagnetic waves in homogeneous and random discrete and continuous environments. Time reversal methods based on the invariance of ...
Master's Thesis in Mechanical Engineering (Applied Design) Abstract of Gas Turbine Rotor Stress Analysis Using Continuous Damage Mechanics In this thesis, Lometer's unified model based on continuous damage mechanics is used to model the stress-strain behavior of a gas turbine rotor sample. The unified damage law, which is used to model creep-fatigue interaction, is based on the ...
Master's Thesis in Mechanical Engineering (Applied Design): Abstract of the analysis of leading damage in pin connections of composite materials. The purpose of this research is to analyze the leading damage in pin connections of composite materials. To do this, finite element software ABAQUS and FORTRAN programming have been used. The contact between the composite plate with ...
Master's Thesis in Energy Systems Abstract Crude oil distillation unit is one of the most important and critical operational units of any refinery. This unit often requires revision in the design of the structure (Revamping) or making small changes in its existing condition without the need to reduce or increase the basic process devices (Retrofitting) in order to achieve higher ...
Master's Thesis in Agriculture Majoring in Agriculture (M.Sc) Abstract In order to investigate the effect of biofertilizers on the quantitative and qualitative characteristics of garden thyme, an experiment was carried out in a greenhouse in an area of ??Semnan in the cropping year of 2010-2011. This experiment was carried out using a 3x3 factorial based on a randomized complete ...
Dissertation for M.Sc degree, specialization: manufacturing and production, abstract in this thesis, how to improve the properties of plastics with the help of heat treatment. First, we will talk briefly about polymers, plastics and their sub-branches and heat treatment on them, and then we will discuss the effect of annealing heat treatment on heavy polyethylene sheets that are ...