Download more than 18 examples of thesis, proposal and project topics about drilling in editable WORD file format at undergraduate, graduate and doctoral levels for use and reference in research, articles, theses, student and academic projects.
Dissertation for Master's Degree in Public Administration, Human Resource Management, Abstract The purpose of this research is to investigate the relationship between social capital and talent management system in Iran's National Drilling Company located in Ahvaz. This research is applied and correlational in terms of purpose. The employees of Iran National Drilling Company ...
Dissertation for M.Sc degree in soil and soil mechanics engineering, summer 2013, first chapter, introduction of micro candles 1-1 Micro-candles in general in dealing with problematic soils
Dissertation for Master's Degree (M.A.) Direction: ""Domestic Business"" Introduction in Management Science To increase the performance of employees of an organization, various strategies have been proposed, such as increasing job satisfaction, applying continuous monitoring and implementing incentive and punishment programs, and other cases. In addition to the above solutions, ...
In order to obtain a master's degree in the field of civil engineering - soil and foundation orientation, Abstract Nowadays, circular foundations are more or less used for structures, especially structures that have axial symmetry. In this research, a numerical study was conducted on bearing capacity and settlement of annular foundation. PLAXIS software was used for modeling. ...
Dissertation for Master's Degree in Civil Engineering - Marine Structures Abstract In this research, while using the results of SPT and CPT tests carried out in 4 different points of the Shahid Rajai Port Development Project site and using the methods of Seyed Idris and Robertson Ride, the liquefaction potential of the region is evaluated. Such an agent
Dissertation for Master's Degree in Civil Engineering, Marine Structures, Abstract: Tension-based platforms are among economic marine platforms for use in deep waters. The correct prediction of the platform's dynamic response to environmental loads is very important in its economic and safe design. In this research, the dynamic behavior of the tension base platform under the ...
Dissertation for master's degree in civil engineering, structural orientation. Abstract Good bond strength between the old and new concrete surface is a key factor in the performance of concrete repairs. The purpose of this thesis is to investigate and evaluate the bond strength between the surface of the old concrete and the added concrete. In this thesis, a laboratory research ...
Master's thesis in the field of chemical engineering (gas engineering trend) in recent years, many horizontal wells have been drilled around the world. The main reason is the ability to increase the level of the tank in contact with the well, which increases the utilization of the well. Well testing is used to identify the models of hydrocarbon reservoirs and to identify their ...
Master's thesis in the field of chemical engineering, abstract of the laboratory study of iron oxide production on a microstructural scale using the precipitation method with supercritical anti-solvent by: One of the problems of cement used in oil wells, which are used to connect wall pipes and well walls, is that these cements do not have the desired resistance against high ...
A master's thesis in the field of chemical engineering. Abstract of the laboratory study of the wear phenomenon of gas containing sand and liquid droplets in pipelines. For this purpose, a pipeline test device including: vertical and horizontal pipelines and various connections has been made. The studied fluid consists of three phases: gas, liquid and solid. The gas phase is ...
Master's Thesis in the field of Chemical Engineering (no orientation) Abstract of the laboratory study of the wear phenomenon of liquid containing sand in pipelines. The studied fluid consists of two phases, liquid and solid. The liquid phase is water, and sand particles form the solid phase. In this research, the parameters affecting the wear rate, including: fluid speed, sand ...
Field of study: Mechanics, orientation: energy conversion. The present research was conducted in order to investigate the movement of pig in pipelines. Due to the importance of pipelines in providing energy resources in the world, after installation and operation, the maintenance of these lines is of high importance, which has caused special attention to be paid to the design of ...
Dissertation for Master's Degree in Electrical-Electronic Engineering (M.Sc) Abstract Sulfur recovery process by Klaus method is one of the most common methods of separating elemental sulfur from acid gas resulting from the sweetening process in gas and oil refineries. But due to the complexity of this process and the multivariable nature of the reaction furnace and the lack of ...
Dissertation for Master's Degree in Mining Engineering - Rock Mechanics Abstract Today, blasting operations in hard rock piles is an inevitable thing in many mining and construction projects, and in case of inaccuracy in its design, it can cause great loss of life and money to all construction or mining projects. When an explosion takes place in two different rock masses with ...
Dissertation for Master's Degree in Rock Mechanics Introduction Excavations made in rocks have different dimensions according to their purpose and vary from small dimensions to dimensions comparable to huge concrete structures. Surface excavations can be used as a space for extracting mines, creating buildings, and supporting and overflowing dams, factories, power plants, as ...
To obtain a master's degree in mechanical engineering - manufacturing and production. Abstract: The electric discharge machining process is one of the advanced machining processes, which is one of the important applications of this process. Despite the unique applications of this machining method, low chipping rate, high surface roughness, high tool wear rate and environmental ...
Dissertation for Master's Degree in Mechanical Engineering, Manufacturing and Production, Abstract: The process of laser forming, especially in recent years, has been widely noticed. In this process, shaping is done by irradiating the laser beam on the surface of the sheet, which is accompanied by a rapid local heating and subsequent cooling of the heated area. However, the way ...